Home > Flashings > Applications: Residential Application

Residential Application


Instructions Products
GABLE FLASHING
  1. In some cases you may have to bend the edge of the panel up 1"
  2. Place sealer tape along edge of roof panel in line with the gable flashing flange
  3. Install flashing by firmly pressing flashing onto sealer tape. Fasten with coloured screws
  4. Fasten flashing to panel with screws through the sealer tape
back to top

Slate
Prolok
RIDGE/HIP FLASHING
  1. Attach the roof panels 1½" down from the ridge
  2. Check the overhang of the roof at fascia min 1"
  3. Attach closures to the roof panels at ridge
  4. Attach z bar over closures and roof panels
  5. Attach the gable flashing
  6. Fasten the ridge cap to z bar with stitch screws
back to top

Slate
Prolok
Dekk-Tile
ROOF TRANSITION
  1. Attach roof panels down from transition
  2. That distance must be lower than the bottom of the upper roof panel
  3. Check overhang of the roof at fascia min 1"
  4. Attach closures to the roof panels at transitions
  5. Attach z bar over closures and roof panel
  6. Fasten transition with nails to roof sheeting
  7. Fasten transition with stitch screws to z bar
  8. Attach sealer tape as shown
  9. Attach uphill panels as shown
back to top

Slate
Prolok
VENTED CLOSURE
  1. Decking should be held back 1½" from the ridge
  2. Attach roof panels
  3. Check overhang of the roof at fascia min 1"
  4. Attach vented closures
  5. Attach gable flashing
  6. Fasten ridge cap
back to top

Prolok
END WALL
  1. Attach roof panels 1½" down from the end wall flashing
  2. Attach closures to the top of the panel
  3. Attach z bar as shown
  4. Nail end wall flashing to wall
  5. Screw flashing to z bar
back to top

Prolok
SIDE WALL
  1. In some cases you may have to bend edge of panel up 1"
  2. Place sealer tape along edge of roof panel in line with the gable flashing flange
  3. Install flashing by firmly pressing flashing onto sealer tape. Fasten with coloured screws
  4. Fasten flashing to panel with screws through the sealer tape
back to top

Slate
Prolok
W-VALLEY FLASHING
  1. Starting at the eave trim, place the valley flashing so it overhangs by 1"
  2. Caulk and lap subsequent flashing 6"
  3. Place 2 rows of sealer tape parallel to the valley
  4. Fasten down flashing with roofing nails
  5. Roof panels should start 4" from the center of the valley flashing
  6. In heavy snow areas keep roof panels back 6" to 8" from the center of the valleys

back to top

Slate
Prolok
Dekk-Tile
EAVE FLASHING
  1. The eave flashing must be installed before roof panels
  2. Fasten the eave flashing with roofing nails
  3. Roof panels must overhang fascia by 1"
back to top

Slate
Prolok
PEAK CAP APPLICATION
  1. Attach roof panels 1" to 1½" down from peak
  2. Attach closures to top of panel
  3. Attach z bar over closures
  4. Screw flashing to the z bar with stitch screws
back to top

Prolok
DRIP CAP
  1. Attach flashing with roofing nails
  2. Drip flashing over some windows and doors may have the color on the other side
OUTSIDE CORNER
  1. Attach J flashing with nails
  2. Some corner flashings may require a J flashing for support
 
INSIDE CORNER
  1. Attach J flashing with nails
  2. Some corner flashings may require a J flashing for support